Sign in to follow this  
Followers 0
sxshooter

Spare Battery Installation on my Truck

5 posts in this topic

My brother has been after me to get an electric cooler for my hunting trips in my truck. He has two now and has offered to let me use them for an upcoming trip to the Dakotas (from CA).

So, I needed to install a couple power receptacles (cigarette lighter plugs) in the bed and thought it would be prudent to install a second battery

After reading a bit on this forum, I ordered a Painless 40120 Digital Power Manager from Summit Racing. It arrived promptly and I was ready to start the installation yesterday after work. When I openned the box I noted that the only thing in the box was the module and the wire bundle. There was no hardware, connectors, bolts, heat shrink, or electrical insulating boots for the terminals.

So, in the interest of getting this project done this weekend, I headed to an autoparts store looking for these items. O'Reilley = no luck. Pep Boys = no luck. Electronics store = heat shrink & connectors, no boots. West Marine = boots and large connectors. 2 hrs and 20 miles of driving in rush hour in L.A. and the associated gas, I had my hardware. I figure I'm $8 in gas and about $20 in parts into this, plus the $200 "Painless" part.

DSC_5658_zps07d5df36.jpg

Aux battery installation. I used a factory clamp and bolt $6-7 at the dealer.

DSC_5646_zps5c9dd89a.jpg

DSC_5644_zpsf62ca229.jpg

I tied from the Painless module to the fuse block on the firewall, because it was more convenient than tieing directly to the battery.

DSC_5652_zps3e91f5c7.jpg

Trimmed the fuse cover to allow for the cable out the top left.

DSC_5653_zpsc60323c0.jpg

The kit comes with enough wire to run 5 ft from the aux battery to the module then another 5 ft to of cable to the main battery. I wanted the module behind the main battery. That took 10 ft of cable from the aux battery. I decided I'd bump the cable gauge from 6 ga to 4 ga for a 10 ft run. $30 worth of cable at West Marine and some cable ends

DSC_5650_zps34073af6.jpg

DSC_5657_zps87eba00a.jpg

My location for the green flashing light...for now. I was finding it a pain to find a firewall penetration to run the wire so I just put the light outside in the plastic corner trim of the windshield. Short wire run, easy to replace the corner trim.

So, it was almost $200 for the "Painless" module. About $125 for a DieHard online w/tax. Probably another $75 in cables, hardware, etc., plus the countless trips to stores. Call it another $100. So, maybe $400-425 for this installation.

I hope this Painless thing is trouble free and an works when needed. But, by its very nature of design, you will likely never know if you've drained your main battery and the aux battery provides an assist to starting the truck. This system is not supposed to let a slow current draw drain the aux. Normal slow current draw should drain the main battery, then, when a large (starting) load is encountered and the main is unable to provide all the current, the smart circuit in the Painless module is suppose to trip the relay to assist the start load. In normal running, the Painless circuit is supposed to let the main battery be charged up first, then allow the aux battery to get a charge next. Theoretically, the aux battery should always be there fully charged for assisting the main battery in the event it's needed to help start the engine. I may never find out if it works. I change batteries at 5 years as a matter of judgement to prevent being stranded on a hunting trip in the middle of timbuktu. That has worked well for me.

Share this post


Link to post
Share on other sites

That is an expensive set up,

but if it works for you, good on you.

Tom

Share this post


Link to post
Share on other sites

Tom,

Yeah, pricey, but it'd still cost 2/3rds that if I built up a traditional manually operated one with the same quality battery, cables and hardware. I didn't wanna scrimp on this cause it may help save from a ruined hunt trip someday.

Share this post


Link to post
Share on other sites

A second battery done right is a lifesaver any way you look at it. Very nice install Chuck. Almost anything worthwhile costs a bit more but it should preform flawlessly. Love the pictures too. :good:

Share this post


Link to post
Share on other sites

I agree. A very well written, detailed post of a very sanitary job. Well done.

I've installed a couple backup batteries in my rigs. For a proper job your price is right inline.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now
Sign in to follow this  
Followers 0