Jump to content
BPS

I had to make me a weazel ball decoy...

Recommended Posts

BPS    1

I had just ordered a pair of weazel balls a few days before Varmint Al posted up his Singing to the Coyotes Video with the New & Improved version of the Weazel Ball Decoy. Shown here on his site.I had plans to make one of the traditional decoys, but after seeing his video & the "How To" on his site, I just had to build one.But I did not have a welder or any close friends near by with one either.I already had several pieces of 3/16" steel rods a little over 2' long, so I just put the end of one, in my bench vise & made a 2" long 90 degree bend, then I ground a sharp point on the other end of the rod, to stick it in the ground.I wanted to be able to securely attach the weazel to the stake & still be able to change the batteries & transport it easily.What I settled on, was bending the end of the rod to wrap around the motor of the decoy. I left a small amount of play in it so I could remove the decoy without to much trouble.I did this using my bench vise, a 4lbs. hammer & a pair of pliers. I had to play with it a bit to get it just right.Heres a picture of the rod I bent.IMG_1737.jpgHeres with the Weazel Ball attached, I used a small piece of 1/8" Camo Bungee cord to hold the motor in place.IMG_1735.jpgLike I said before I do not have a welder so I had to think outside the box a little bit, plus I'm notoriously cheap & I'm pretty good at Afro Engineering, so I had to figure out a way to make the little piece to stick out, that the tail of the weazel ball hits & makes it flip erratically.I took a 4" long piece of the 3/16" steel rod & bent it to 90 degrees.While still trying to figure out how to attach it to the other rod, I looked down on my work bench & saw a cheap Black & White, Bic Ink Pen, I pulled it apart & the 3/16" rod slid right inside with just a little bit of slop in it. A single wrap of electrical tape around the steel rod made it nice & snug.I cut the pen in half & simply taped it to the 3/16" rod, the small 90 degree piece I made slid right inside, but is snug enough that it doesent move when the tail of the decoy hits it.IMG_1739.jpgIMG_1741.jpgI actually prefer this method to welding it in place, since I can remove the small 90 degree piece for easier transport which is another plus, but its also something else to misplace.The rod I started out with was 2' tall, but I wanted to copy the original design as much as possible, to make it compact & easily packable, but I did not have anything to couple 2 of the rods together, so I scrounged up another Bic Pen & removed the guts & used it for a coupler.I cut the 2' tall rod in half, I had to put a tight wrap of electrical tape on the end of the ground rod, so that the Bic Pen would fit snugly. I pushed it onto the bottom rod about 2" & its snug enough to stay in place.IMG_1744.jpgI coupled the 2 rods together using my highly scientific "Bic Coupler" & it actually helped add a bit of motion due to the joint in the middle of the rod, which allows the decoy to spin 360* I painted everything kacki & olive drab (My 2 favorite colors in the world)Heres everything layed out together.IMG_1745.jpgHere it is in working order.IMG_1732.jpg

.
Hope you guys like it.Thanks again to Varmint Al for posting that video up, Lee

Share this post


Link to post
Share on other sites

Lee, pretty clever! With your talents, who needs a welder? By the way, how is it coming with getting your FoxPro fixed?

Share this post


Link to post
Share on other sites

Hey Mick, you know that Prey Master I was telling you I had to send back? Well, I did and they found some real problems with it. But for $60 they are going to send me a new unit and remote. Can't beat that for a caller I bought used. By the way guys, it is a PM 4.

Share this post


Link to post
Share on other sites

Braz----good job! Between my decoy, that kind of looks like Lee's and my PM3, I should do OK, if it ever stops snowing up here.

Share this post


Link to post
Share on other sites

Yea I know. I can't get to my cabin. And it's suppose to be snowing up there, starting next Tuesday, for another 5 or 6 days. Dang, not sure when I'll get there.

Share this post


Link to post
Share on other sites
BPS    1

Mick,The Fox Pro is working great now, I just need time to escape & do some more calling. You'll have to tell me about your new caller & your decoy.Braz, Good luck on making it up the hill, I heard the same weather report, Lord knows we need the Snow up in the hills, but it still makes it tough on anyone who lives up there.Glad you guys liked the decoy.Lee

Share this post


Link to post
Share on other sites

Very cool on the decoy, Lee. Coincidentally, I have one en route to me as we speak. And I don't have a welder either. ;) I'll put this thread to use. Thanks.

Share this post


Link to post
Share on other sites

Thanks Lee. I put up a link to your YouTube video and also to this thread with the construction pictures. By the way, I have generated a new calling sequence with the Excruciator call from Butcher. There is a link to the MP3 file on my Coyote hunting page. It has been downloaded more than 4,000 times already this month. You guys are welcome to download it. It is at the top of the list of free calling sounds.Good Hunting... from Varmint Al coyotel.gif

Share this post


Link to post
Share on other sites
BPS    1

Thanks Al, I sent you a PMI'll have to check out the new calls & add to my arsenal :smiley-innocent-halo-yellow: Lee

Share this post


Link to post
Share on other sites

I built mine this weekend. Went with a super simple approach because I didn't have a lot of time. I took a piece of 1/4" threaded rod and simply drilled a hole through the plastic "fin" that is on the battery compartment. I put threaded nuts on either side of the fin, and viola! Painted it, staked it in the ground, and it works like a charm. We'll see if it's strong enough to hold up over time. Works for now. Total cost = ~$8.00 (including shipping from amazon).

Share this post


Link to post
Share on other sites

We need a close up picture of that!

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×